ANYCUBIC Multicolor PLA
品牌 ANYCUBIC · 3D打印耗材（线材与树脂） · 3D打印 · 更多 ANYCUBIC 商品
- 材料: PLA（聚乳酸），可生物降解，气味小
- 直径: 1.75毫米
- 直径公差: ±0.02毫米（根据ANYCUBIC商品页面和多位评测者）
- 净重: 每 spool 1公斤，共计10公斤
- 长度: 每 spool 约340米
未标价
- ANYCUBIC前往 ANYCUBIC
- eBay前往 eBay
- Amazon前往 Amazon （付费链接）
- eBay (used) eBay: used, open-box, refurbished前往 eBay (used)
商店按固定顺序排列，绝不按价格或佣金排序。 价格仅为快照，请以商店当前价格为准。
摘要
ANYCUBIC Multicolor PLA是一款适用于高容量的爱好者、打印农场、教育工作者以及ACE Pro用户的10公斤、10色1.75毫米PLA套装。在购买前请检查进料设置：交叉绳结、略大的 spool 肩部和硬挺的材料可能会在自动多色切换器（如Bambu Lab AMS和Creality CFS）中卡住。
优点
- 10色入门调色盘的 per-kg 价值优异。
- 在独立 direct 挤出机上层间隙融合顺畅，拉丝现象极少。
- 标准非白色颜色展现浓郑的色彩饱和度。
- 在彻底清洗过的纹理 PEI 板上第一层粘附可靠。
- 内置智能识别功能，适配 ANYCUBIC ACE Pro 设备。
- 盘绕整齐，无交叉绕缠，clog 且 bubble 免疫。
缺点
- 频繁的盘绕覆盖现象导致卡料及长时间打印失败。
- 略宽的 spool 肩部会引发第三方仓和自动进料器中的间隙及回抽错误。
- 白色耗材存在粗糙的直径局部和更高的卡料率。
- 硬挺的聚合物成分抵抗多次机械回抽，可能引发误判的纠结报警。
- 部分 spool 可能真空封损坏需烘干。
- 多色套装无 manufacturer 规格表；商店页面缺少可打印的 nozzle 与 bed 参数表格。
已核实规格
| 材料 | PLA（聚乳酸），可生物降解，气味小。 |
|---|---|
| 直径 | 1.75毫米。 |
| 直径公差 | ±0.02毫米（根据ANYCUBIC商品页面和多位评测者）；一位实测 testers 显示标准PLA的最大偏差为0.01毫米。 |
| 净重 | 每 spool 1公斤，共计10公斤。 |
| 长度 | 每 spool 约340米。 |
| 颜色 | 黑色、白色、纹理灰色、透明、红色、蓝色、绿色、橙色、黄色、紫色（共10色）。 |
| 挤出 nozzle 温度 | 根据 10公斤 bundle 评测为200-210°C；根据实测标准PLA测试为190-230°C；社区 profile 推荐210°C。 |
| 热床温度 | 50-80°C；用户反馈多集中在彻底清洗后的纹理 PEI 表面上的55-60°C；社区 profile 推荐55°C。 |
| 拉伸强度 | 至少55 MPa。 |
| 硬度 | 81D。 |
| 气泡含量 | 无。 |
| 识别芯片 | 兼容 ANYCUBIC ACE Pro，支持自动识别类型、颜色和打印 profile；在没有ACE Pro的打印机上 inert。 |
| 最大体积流量 | 约11.62mm³/s（根据社区 profile）。 |
| spool 类型 | rigid 塑料真空包装配干燥剂。 |
| spool 边缘（flange） | 略宽于竞品品牌，可能在狭 tight 的自动干箱中摩擦。 |
| spool 尺寸（标准单 spool） | 含1公斤耗材+0.35公斤 spool；高度60毫米，内径75毫米，外径200毫米。未核实 bundle 套装中的 spool 是否共享完全相同的尺寸。 |
| 烘干 | 如真空封破坏或耗材潮湿，请在45°C下烘干4-6小时。 |
| 保质期 | 据报告 ANYCUBIC 10公斤 PLA bundle 未拆封可保存12-18个月；但未针对多色套装特别验证。 |
完整研究笔记与来源
Print temperatures and bed adhesion
Owner feedback centers bed adhesion at 55-60 C on thoroughly cleaned textured PEI. Drying before first use is recommended by multiple sources despite vacuum packaging. ANYCUBIC’s own store pages for this bundle contain no printable spec table, so treat the temperature ranges as third-party guidance, not manufacturer data.
Feeding in automated switchers
The bundle’s main liability is mechanical feeding. Owners report crossed winds that snag mid-print, spool shoulders that rub in tight feeders, and a polymer stiff enough to resist the repeated retractions that automated switchers impose. The white spool is the outlier, with rough diameter spots and more frequent clogs than the companion colors. None of this disqualifies the bundle for open, direct-drive printing, but it does make unassisted multi-color switching a gamble. Rigid plastic spools avoid dust shedding in enclosed feeders, and the flange is slightly wider than competing brands, which can rub inside tight automated dry-boxes.
Drying, storage and shelf life
Filament is a consumable with no repair path. Keep spools dry; dry at 45 C for 4-6 hours if a vacuum seal is popped or the filament is wet. Vacuum-sealed packaging with desiccant arrives on most spools, but some may arrive with compromised seals. Shelf life of 12-18 months unopened is reported for an ANYCUBIC 10 kg PLA bundle; it is not verified for the multicolor bundle specifically. No warranty or return terms for this filament were found in the sources read.
Value and ownership cost
Value is the bundle’s clear strength. It sits in a $130-150 bulk tier by one aggregation, and as low as about $8.90 per kg by another listing that may be a glow-in-the-dark variant. Bundles of this type typically save 10-30% per kg versus buying the same spools individually. At roughly $15 per kg or less (about $150 or less for 10 kg), the bundle is strong value for single-extrusion workhorses, print farms, educators and ACE Pro owners. At $10-15 per kg it remains a good buy for direct-drive users who monitor spools. Value drops for users expecting unassisted multi-color switching. The ACE Pro chip integration is a differentiator only for ANYCUBIC ACE Pro owners; for everyone else it is inert. Compared with premium brands sold by the kilogram, the bundle’s per-kg price is far lower; the trade-off is batch-to-batch and color-to-color consistency, especially the white spool.
Which model this is
This page covers the 10-color, 10 kg ANYCUBIC Multicolor PLA bundle: black, white, texture grey, clear, red, blue, green, orange, yellow and purple, at 1.75 mm, with an intelligent identification chip on each spool for the ANYCUBIC ACE Pro multi-material system. The chips are inert on printers without ACE Pro. It is a consumable filament, not a numbered model; do not confuse it with single-color ANYCUBIC PLA, PLA+, PETG, silk or glow-in-the-dark bundles. The Amazon listing for this bundle is ASIN B0F2SH32F3.
来源
Manufacturer:
- ANYCUBIC filament pack (US store)
- ANYCUBIC filament pack (global store)
- ANYCUBIC 1.75mm PLA filament (US store)
- ANYCUBIC filament performance comparison
Independent reviews:
Owner reports:
- No dedicated owner threads were found; owner evidence here comes through third-party review aggregation.
