
Creality Hyper Series PETG-CF Filament - Danxia Red
Бренд Creality · Филамент и смола · 3D-печать · Ещё товары Creality
Все модели категории «Филамент и смола» рядом →
- Filament diameter: 1.75 mm
- Material: PETG, carbon fiber reinforced composite
- Density: 1.24 g/cm³
- Tensile strength (X-Y): 44.9 MPa
- Elongation at break (X-Y): 8.7 %
Минимальная найденная цена
$19,99
от $19,99 в Creality · Проверено 6 нояб. 2026 г.
- Creality $19,99Открыть: Creality
- AmazonОткрыть: Amazon (платная ссылка)
Ещё на eBay (1)
- eBayОткрыть: eBay
- eBay (used) eBay: used, open-box, refurbishedОткрыть: eBay (used)
Магазины с ценой идут от дешёвых к дорогим; комиссия никогда не меняет порядок. Цены — это снимки на момент проверки. Уточняйте актуальную цену в магазине.
Кратко
A 1.75 mm, 1 kg carbon-fiber-reinforced PETG filament for FDM printers that needs a hardened steel nozzle and a printer that can hold 240-260 °C with a 70-90 °C bed. The matte red finish reduces clogging and is suitable for functional parts, but keep it dry and check your nozzle before buying.
Сильные стороны
- Carbon fiber reinforcement gives a matte, low-reflectivity finish that’s good for functional parts.
- Published mechanical properties show high tensile and flexural strength for a tough filament.
- Manufacturer claims reduced nozzle clogging compared to standard PETG.
- Creality’s own US storefronts price it at $16.99-19.99 per kg against a $29.90 list price.
- RFID identification on the spool for tracking and inventory management.
Слабые стороны
- Requires a hardened steel nozzle, which is an additional cost for printers with standard brass hotends.
- High temperature requirements exclude some printers and build plates (240-260 °C nozzle, 70-90 °C bed).
- The filament is hygroscopic and requires dry storage, with a drying cycle at 60 °C for 8-12 hours if needed.
- No independent laboratory test data exists for this exact variant to verify the manufacturer’s claims.
- Small sample size in store feedback across maker storefronts.
- Color naming is inconsistent between Creality’s channels (“Danxia Red” vs “Rocks Red”).
Проверенные характеристики
| Filament diameter | 1.75 mm |
|---|---|
| Material | PETG, carbon fiber reinforced composite; matte sandblasted surface |
| Density | 1.24 g/cm³ |
| Tensile strength (X-Y) | 44.9 MPa |
| Elongation at break (X-Y) | 8.7 % |
| Flexural strength (X-Y) | 88.1 MPa |
| Impact strength (X-Y) | 64.4 kJ/m² |
| Flexural modulus (X-Y) | 4324.4 MPa |
| Interlayer adhesion strength (Z) | 9.5 kJ/m² |
| Net weight | 1 kg / 2.2 lb |
| Gross weight | 1.29 kg / 2.8 lb |
| Package dimensions | 210 × 210 × 70 mm |
| Recommended printing temperature | 240-260 °C |
| Recommended bed temperature | 70-90 °C |
| Recommended printing speed | 30-300 mm/s |
| Recommended fan speed | 80 % |
| Recommended nozzle | hardened steel or other wear-resistant nozzles |
| Recommended print surface | carbon-silicon crystal or PEI sheet |
| Post-processing | sanding or heat gun treatment |
Полные заметки исследования и источники
Material properties and printing requirements
Creality Hyper PETG-CF Danxia Red is a carbon-fiber-reinforced PETG composite that differs from plain Hyper PETG in both specifications and recommended settings. While the standard Hyper PETG uses 190-260 °C nozzle temperatures and 45 °C beds, the CF variant requires 240-260 °C and 70-90 °C to handle the abrasive carbon fibers [1][4].
The mechanical specifications published by the manufacturer show density of 1.24 g/cm³, tensile strength of 44.9 MPa, and flexural strength of 88.1 MPa, with a reseller comparison table adding impact strength of 64.4 kJ/m² and flexural modulus of 4324.4 MPa [1][4]. These figures suggest a material optimized for toughness and durability, though no independent verification exists for these claims.
The carbon fiber content also gives the filament a matte, sandblasted appearance that reduces reflectivity and, according to the manufacturer, helps minimize nozzle clogging and material buildup during printing [1][4]. This matte finish means the red color will appear darker and less glossy than standard PETG reds.
Nozzle and hardware requirements
The most important consideration before buying is the nozzle requirement. Creality explicitly states that hardened steel or other wear-resistant nozzles are required for this filament [1][4]. Carbon fibers are abrasive and will quickly wear down standard brass hotends, making the nozzle cost a significant part of the total ownership expense.
Printers must also meet the temperature requirements: a 240-260 °C nozzle and 70-90 °C bed. This excludes some entry-level printers and certain build plate types that can’t reach these temperatures. The recommended print surface is carbon-silicon crystal or PEI sheet, with post-processing involving sanding or heat gun treatment to achieve the best finish [1][4].
Storage and maintenance
Like all PETG filaments, this material is hygroscopic and requires careful storage. Creality’s guidance for the Danxia Red product specifically recommends keeping it in a dry, ventilated place away from heat, sunlight and humidity [4]. If the spool won’t be used up soon after opening, a drying box should be used.
The manufacturer’s general PETG drying chart recommends 60 °C for 8-12 hours when moisture symptoms appear, with spool label and product-specific instructions taking priority [7]. Regular maintenance includes keeping the spool sealed and monitoring for moisture, which can cause print quality issues if not addressed.
Pricing and value
Creality’s own pricing shows significant discounts from their list price. The US store lists 1 kg at $19.99 against a $29.90 compare-at price, with multi-spool tiers of $16.99 (5 spools), $15.99 (10 spools), and $14.99 (20 spools) [1]. The US dev store offers the same RFID SKU at $16.99, also against $29.90 [2]. The global VIP Mall lists the price at $29.90 with dealer access on application [3].
At roughly $17-20 per kilogram from the manufacturer, this represents good value for a carbon-fiber-reinforced PETG, provided you already have a hardened nozzle and a printer capable of the required temperatures. The value proposition is strongest for makers who want a matte, tough composite material without the gloss of standard PETG or PLA.
The honest limitation is that the case is entirely specification-based. No independent instrumented test of the CF variant could be found, so claims about outdoor durability, weather resistance and chemical resistance remain manufacturer claims rather than certified properties [1][4][7].
Источники
Manufacturer:
- Creality Hyper PETG-CF RFID 3D Printing Filament 1kg
- Hyper PETG-CF RFID 3D Printing Filament 1kg (Live Exclusive)
- Creality VIP Mall - Hyper PETG-CF
- Creality Hyper PETG CF Danxia Red Filament 1kg
Independent reviews:




