Creality High-Speed PLA Filament 1.75mm 2Kg: обзор, плюсы и минусы

Creality High-Speed PLA Filament 1.75mm 2Kg

Material: polylactic acid (PLA) high-speed polymer blend

Diameter: 1.75 mm.

Dimensional tolerance: ±0.14 mm per the manufacturer

Density: 1.25 g/cm³

Tensile strength: about 52–53 MPa

Цена не указана

Новые

Б/у, восстановленные, вскрытые

eBay (used) eBay: used, open-box, refurbishedОткрыть: eBay (used)

Магазины идут в фиксированном порядке — не по цене и не по комиссии. Цены — это снимки на момент проверки. Уточняйте актуальную цену в магазине.

Кратко

High-speed PLA filament for modern FDM printers, formulated for stable extrusion up to 600 mm/s on capable hardware. Check your printer’s hotend flow and cooling before buying: top speed needs both, and under-cooled prints can weaken layer bonding.

Сильные стороны

Consistent high-speed extrusion without clogging or excessive stringing at elevated speeds.
Excellent first-layer adhesion on PEI, glass, carbon-silicon and glue-prepared build plates.
Smooth surface finish and sharp detail on functional parts and tabletop models.
Tight diameter control that reduces auto-leveling sensor false triggers.
Rapid cooling solidification keeps geometry clean at 500 mm/s test speeds.

Слабые стороны

Top speeds need a high-flow hotend and sufficient part cooling; older printers may under-extrude.
Slicer profiles must match the printer’s volumetric flow limit or dense infill under-extrudes.
Under-cooling at speed can weaken layer bonding.
Costs more than generic bargain PLA spools.
Paper spool flanges need care to avoid edge crushing.

Проверенные характеристики

Material	polylactic acid (PLA) high-speed polymer blend.
Diameter	1.75 mm.
Dimensional tolerance	±0.14 mm per the manufacturer; independent tests report ±0.03 mm (mean deviation under 15 μm).
Density	1.25 g/cm³.
Tensile strength	about 52–53 MPa.
Flexural strength	about 92 MPa.
Print temperature	190–230°C.
Bed temperature	25–60°C.
Maximum print speed	up to 600 mm/s under optimized conditions.
Spool format	2 kg total, typically two 1 kg spools.
Spool	recyclable paper spool and packaging.
Composition	non-toxic, odor-free bio-derived polymer blend.

Полные заметки исследования и источники

Требования к скорости и оборудованию

The 600 mm/s figure is an architectural ceiling, not a default. Real throughput depends on hotend melt capacity, volumetric flow rate, part geometry and cooling fans. Independent tests ran clean prints at 500 mm/s with 0.25 mm layer heights, with minimal stringing and good bridging. If your printer cannot push the required volume, the same filament behaves like ordinary PLA at lower speeds. Newer spool revisions add RFID tags for compatible multi-material feed units; standard printers read the filament as ordinary material.

Диаметр и механические свойства

Both reflect factory quality thresholds across batches and measurement methods. Independent benchmarks report tensile strength near 53 MPa and flexural strength near 92 MPa, above standard PLA and standard ABS baselines. Those advantages hold under specific test standards and do not make this an engineering-grade filament for extreme heat or structural loads. Either way, the practical result is stable extrusion and fewer auto-leveling sensor errors across long runs.

Хранение и обращение

Store the filament dry; PLA absorbs ambient moisture over time, so desiccant storage or drying is needed after humidity exposure. The recyclable paper spool needs care to avoid edge crushing during aggressive rewinding. Warranty coverage runs up to 12 months for defects through authorized retail channels. Recurring ownership costs are limited to electricity, replacement nozzles (hardened steel is recommended for abrasive variants such as carbon-fiber blends) and desiccant storage upkeep.

Стоит ли покупать?

Excellent value at $20 per kg or less, fair from $21 to $25, and premium above $25. The lower tier needs multi-roll or bundle pricing to reach, since single 1 kg spools list around $19.99 at the official store with tier discounts lowering per-roll cost. Above $25, RFID ecosystem integration or specific colorways have to justify the price against competing high-speed PLA.

О какой модели идёт речь

This page covers the Creality High-Speed PLA Filament (Hyper Series), 1.75 mm, in the 2 kg bundle (typically two 1 kg spools). Newer spool revisions add RFID tags for compatible multi-material feed units; standard printers read the filament as ordinary material. The Amazon listing for this bundle is ASIN B0CT5S3BHK. Do not confuse it with Creality’s standard PLA or other filament lines.