Skip to content
Sunlu SP2 Filament Dryer

Sunlu SP2 Filament Dryer

By SUNLU · Filament Dryers · 3D Printing · More from SUNLU

Compare all Filament Dryers side by side →

  • Rated power 250 W
  • Heats to 70 C in 15 minutes
  • Capacity 2 rolls of 1 kg or 1 roll of 2-3 kg filament
  • Supports spool diameters up to 250 mm and widths up to 153 mm
  • Net/gross weight 3.6 / 4.1 kg

Lowest price seen
$154.99
from $154.99 at eBay · Checked Nov 9, 2026

New
Used, refurbished, open-box

Stores with a price are sorted lowest first; commission never changes the order. Prices are snapshots. Check the current price with the store.

From $154.99 at eBayView at eBay

Problems, parts and running costs

Summary

A modular filament dryer and sealed storage box for people running several open spools of PLA, PETG, TPU or ASA, with a 250 W heater base that detaches from the chamber. Check your filament before you buy: the chamber tops out at 70 °C, so Nylon and PC need SUNLU’s E2 instead.

Size in context

27.8 cm · 10.9 in (W) × 20.8 cm · 8.2 in (D) × 39.6 cm · 15.6 in (H)

27.8 cm · 10.9 in (W) × 20.8 cm · 8.2 in (D) × 39.6 cm · 15.6 in (H) · Drawn to scale from the maker's stated dimensions, next to everyday objects.

Strengths

  • The heater base detaches, so one box can dry while another stays sealed and dry.
  • Six gasketed filament outlets let two printers feed from the unit at once.
  • Measured PETG moisture dropped from 0.60% to 0.28% after 6 h, with stringing down about 90%.
  • Chamber humidity held at 20% across a multi-day paused print.
  • Presets and a 0–99 h timer remove the need to research settings per material.
  • Printed straight from the unit during drying with no failed prints from clogging or adhesion.

Weaknesses

  • The display is dim with poor viewing angles and has to be read head-on.
  • There is no dedicated moisture exhaust port, so very wet filament dries slower than in vented models.
  • The unit arrives partly assembled; the hygrometer box, desiccant bag and base-to-chamber fitting need work.
  • The base is not locked to the chamber and can detach when you lift the unit by its handle.
  • The base mates with the chamber in one direction only, and side plugs must be open while drying and closed for storage.
  • 70 °C is not enough for full Nylon or PC drying, which SUNLU points at the E2 for.

Verified specifications

Rated power250 W; the heater element itself is rated 200 W.
Temperature range35–70 °C, reaching 70 °C in about 15 minutes.
Controlsbacklit touchscreen with four touch-sensitive buttons, preset programs for PLA, PLA+, PETG, ABS, TPU, PVA, PVB, ASA and PA/PC, plus manual temperature and time override.
Timer0–99 h.
Humidity readoutbuilt-in hygrometer display range 10–90%, plus a second always-on hygrometer in the storage box that reads humidity without switching on the heater.
Capacitytwo 1 kg spools or one 2–3 kg spool.
Spool compatibilitydiameters up to 250 mm, widths up to 153 mm.
Filament0.25–3 kg, 1.75 mm and 2.85 mm diameters, paper and standard spools, mounted on a horizontal axis so printing can continue with the spool inside.
Dimensions278 × 208 × 396 mm; internal chamber 265 × 193 × 274 mm.
Weight3.6 kg net, 4.1 kg gross for the dryer set.
Sealingsilicone seals on the lid and feet, a multi-layer lid gasket with two locks, six airtight filament outlet caps and gaskets on two airlock feet.
SafetyPTC heater with a metal roller fan, dual temperature protection switches and software control.
In the boxchamber, heater base, hygrometer, desiccant, desiccant box, power cable, spool roller, two airlock feet, PTFE tubes (8 cm ×2, 1 m ×2), assembly pieces and user manual.
Warranty12 months from original purchase date for consumers and 12 months from shipment date for business buyers.
Full research notes and sources

Drying and storage in one box

The base and the chamber are separate pieces. You dry filament on the base, seal the box with its airlock feet fitted, and dry the next box in its place. Extra sealed storage costs only the box, not another set of electronics, and SUNLU recommends stacking up to three units.

Filament runs on a horizontal axis, so the spool can sit inside while the printer runs. ThePhonograph.net used the unit as a fixed spool holder while actively heating filament, with no failed prints from clogging or adhesion across the test prints.

Heat and drying results

Thermal imaging at 3DWithUs showed the heating element reaching about 80 °C while the spools heated to approximately 70 °C.

p3d.mx measured PETG left open for two weeks at 0.60% moisture and 0.28% after 6 h in the SP2, with stringing reduced by about 90%. After a full drying cycle, ThePhonograph.net reprinted its stringing test parts and saw zero stringing. Over-temperature protection was deliberately triggered in a test and shut the unit down within 3 seconds.

The 70 °C figure is a setpoint. It also warns that a spool must tolerate more than 70 °C or it may deform.

Running costs and what buyers paid

Electricity draw is 250 W while the heater runs and ≤1 W in standby. Replacement desiccant and additional storage boxes are the running costs if you expand the system.

Price context from the sources: 3DWithUs listed $89.99 for one base-plus-box set for the first 100 sets and $99.99 after that, with a bundle of one box and two PLA spools at $69.99 then $74.99. Make: tested the unit at $110. The SUNLU US store page showed $76.49 on sale against a $109.99 regular price for the heating base and storage box set in the October 2026 snapshot.

Maintenance and repairs

Fit the PTFE tubes where the filament path curves sharply; the supplied 1 m tubes are shorter than longer aftermarket ones. Keep the chamber closed during a drying cycle, leave the side plugs open while the base is running, and do not block the internal air intake and exhaust vents.

The desiccant is orange at room temperature and turns dark green once saturated. Regenerate it by drying it at 70 °C. The electronics are integrated and no detailed spare-parts catalogue for the SP2 was found, so repairability beyond accessories is unknown. SUNLU’s warranty statement gives SP2 dryers 12 months, allows returns within 7 calendar days and exchanges within 15 calendar days through the original purchase channel, and covers shipping for confirmed quality issues.

Is it worth it?

Around $76 to $99 the SP2 is good value for multi-spool users and hobbyists with limited bench space, given the combination of drying, sealed storage and humidity monitoring. At $100 to $110 it is fair rather than compelling: you pay list price for a plastic-bodied unit with a dim screen, no dedicated exhaust port and required assembly.

If you print only occasional PLA on one spool, this is more machine than you need and a simpler single-spool dryer serves you. For daily Nylon or PC work, SUNLU itself points to the E2 for extended drying and annealing, and positions the SP2 around space saving and flexibility.

One thing to weigh: independent evidence is thin. No major US test outlet covered the unit, and no Reddit or forum owner threads were found for this model, so the case rests on four specialist reviews rather than a wide ownership history. Nobody has published a failure rate, so treat the durability of the seals and outlet caps as unproven.

Which model this is

This page covers the SUNLU FilaDryer SP2 split-type dryer and storage box, listed by the manufacturer in black, with a 250 W rated heater base and modular stackable chambers. Do not confuse it with SUNLU’s other dryers: the FilaDryer S2 and S4, the S4 Pro and the E2 (up to 110 °C for engineering materials and annealing) are different products with different temperature ceilings and form factors. The manufacturer markets the unit as coming with a battery, but no battery capacity, runtime or charging details are given.

Sources

Manufacturer:

Independent reviews:

Owner reports:

Buying guides for this category

Compare with

See also

Related products