Creality Space Pi V2 Filament Dryer (2-Spool)

What Creality publishes, and what it doesn’t

Creality published the V2 on its US store on 2026-09-22 and lists it at $84.90 with a single variant. The published feature set is short and entirely manufacturer-supplied: up to 75 ℃, 360° hot-air circulation, a second-generation smart sensor, and smart presets with touch control. There is no power rating, chamber size, noise figure, weight, dimension list, timer range or filament-diameter statement in the official text. The product page carries images plus that description, and the V2 has no page on creality.com at all. For a device whose whole job is moisture control before a print, treat this as an incomplete specification sheet rather than a complete one.

The Space Pi family behind the V2

The evidence that does exist is about the family, not the V2. Owners on Creality’s forum discuss the first-generation Space Pi, the Plus and the Dual. The most substantive thread runs from September 2025: an owner whose dryer had sat mostly unused for 10 months threw an E4 error during a long PLA dry and then the unit died outright; a second owner’s Dual threw E4, would not heat with the display still live, and was sent a replacement circuit board under warranty. Several owners say the Dual will not read below roughly 35 % humidity and that silica gel inside the chamber is the practical fix, achieving about 24 % after adding 5 g packs, while a Plus owner reports 15 %. A thread from October 2026 reports a fan that became noisy after about three months, and an April 2026 thread is a request for a replacement blower fan after one failed. A March 2026 thread documents that the top filament outlet will not retain a PTFE tube and that the outlet fitting can be pushed inside the chamber and block filament. None of that is a V2 failure rate, but it is the best available read on how this product line behaves after the box is open.

Running costs, parts and repairs

The visible recurring costs are a replacement blower fan, PTFE tubing for direct-feed setups, and silica gel if the chamber reading will not go low enough. A Creality-branded replacement blower fan for the Space Pi dryer is referenced by a forum user whose fan failed: DC 12 V, 0.6 A, part marking EFB-06E12D/EFS-06E12D. That is evidence a parts channel exists for the line, though it was not verified on a Creality page. Support issued a replacement circuit board under warranty for an E4 fault on a family member, and there is no evidence of a board-repair program specific to the V2. Warranty terms were not verified; Creality’s warranty page is rendered dynamically and exposes separate categories for filament dryers and accessories.

Is it worth it?

At the official $84.90 the V2 is a fair entry purchase with documented gaps and no third-party testing. Between $86 and $95 it is fair, because above the manufacturer price you are paying for availability rather than extra capability. At $96 to $119 it is weak: the buyer is within $2 to $34 of the 4-spool SpacePi X4L at $119.00, which dries four spools in dual independent chambers with 200 W + 200 W PTC heating up to 85 ℃ and an EDry UI. Above $119 the V2 is poor value, because the X4L at $119.00 and the X4 at $159.00 are better-specified tools at or below those prices. If you need two spools and nothing more, the V2 is reasonable; if capacity is the question, step up to the X4L. Confirm the missing specifications with Creality support before buying, and plan to verify filament moisture yourself rather than trusting the on-screen reading.

Which model this is

This page covers the Creality Space Pi V2 Filament Dryer, SKU 4005010128, sold by Creality on its own US store under the handle creality-space-pi-v2-filament-dryer. The Amazon listing is ASIN B0CT59XN7F, which was not verified in this research. Do not merge it with the original Space Pi, the Space Pi V2 Plus, or the 4-spool SpacePi X4 and X4L, which are separate products with different temperature ceilings and spool counts.

Sources

Manufacturer:

• Creality official US store — Space Pi V2 Filament Dryer product page
• Creality official store — Filament Dryer collection page (sibling models and prices)
• Creality official store — original Space Pi product data, archived 2026-06-11
• Creality official website — Space Pi Filament Dryer landing page (no V2 product page on creality.com)
• Creality official — Warranty and Rights Inquiry page

Owner reports:

• Creality Forum — “Creality Space Pi Dryer Problem” (E4 error, board replacement, humidity floor)
• Creality Forum — “Noisy filament dryer | Creality Space PI Filament Dryer”
• Creality Forum — “PTFE tube into Space Pi Dryer not secure”
• Creality Forum — “Modification for Space Pi fillament Dryer”
• Creality Forum — “Creality Space Pi filament dryer - auto off?”
• Creality Forum — “Creality Space Pi FAN” (blower fan replacement)
• Creality Forum — “Creality Space Pi Plus filament dryer”

Search coverage:

• Creality Forum — site search for “Space Pi” dryer (no V2 thread; family threads only)
• 3DPrint.com — site search for “Space Pi V2” (no matching article)
• Redlib Reddit front-end mirror — search for “Space Pi V2” (anti-bot challenge, no results served)