Anycubic Standard Resin (Original Colored UV, Gray, 1 kg): problems, parts and running costs

Checked: 2026-10-25

Summary

Anycubic’s original Standard Resin in Gray is a 1 kg bottle of 405 nm photopolymer, not a printer and not the newer Standard Resin V2, Standard+, ABS-Like or High Speed formulations. Owners report brittle fine features on miniatures and color- or temperature-specific exposure failures; running cost is about $21.99 per kg plus IPA and gloves, roughly $145.90 per year in an illustrative 5 kg scenario. It is a good buy for display prints at or below about $22 per kg with a verified fresh bottle, and tougher alternatives are worth comparing above that.

Common problems and fixes

Brittle miniature limbs and weapons — March 2024 owner report: 7 of 10 game miniatures broke during basing after about 20 minutes of UV curing; other owners reported models shattering after desk bumps and called the resin too fragile for regular miniature handling in November 2024, while one commenter used it heavily without notable brittleness. Fix or workaround: shorter, correctly tested cure cycles or a tougher resin (Standard V2, ABS-Like); changing cure time alone is not a guaranteed fix. Warranty: no verified standalone liquid-resin warranty term was found; contact Anycubic support with order number, photos and bottle batch/expiry. [6][7][8]
Color-to-color settings do not transfer — September 2024: light beige printed reliably on a Photon Mono X2, but a newly purchased Gray bottle produced missing limbs, deformed figures and parts stuck to FEP; 13 of 23 miniatures printed properly at 2.5 s normal exposure on one reported plate. Fix or workaround: recheck plate setup, support geometry, temperature and Gray-specific exposure; test a small exposure coupon at actual print temperature. This is a setup issue, not a warranty-covered defect. [9][2][4]
Poor first-layer adhesion or parts stuck to release film — the original manual advises checking plate leveling, FEP film condition, UV screen contamination and bottom exposure; it proposes trying about 30% longer bottom exposure, and increasing support contact depth or cross-section where supports snap off. No reliable failure rate was found. Warranty: not covered as a profile or material issue; support may advise case by case. [2][9]
Sticky or whitened prints after washing and UV curing — the manual advises rewashing while residue remains, drying thoroughly before UV, and not soaking in solvent over 30 minutes; whitening can come from uncured liquid or solvent left on the surface, and transparent or white colors can yellow with prolonged cure. Fix or workaround: follow the full wash, dry and cure cycle. Warranty unlikely for post-processing errors. [2][13]
Variation with no reliable rate data — owner outcomes vary, and no manufacturer-verified brittle-failure percentage, defective-bottle frequency or adhesion failure rate was found. Fix or workaround: calibrate and test before large plates; keep batch and expiry records. Warranty or support outcomes are case by case. [6][7][8][9]

Parts and consumables

Anycubic Standard Resin, Gray, 1 kg (no exact MPN verified) — $21.99 direct from Anycubic US, October 2026; replenish as consumed. The liquid cannot be reused once polymerized, though uncured vat liquid can be reclaimed by filtering and light-safe storage. [1][2]
99.9% isopropyl alcohol, PureTronics 32 fl oz, part 3125, Micro Center SKU 804237 — $11.99 in-store, October 2026; refresh the wash liquid as it becomes resin-contaminated. An example of suitable high-concentration solvent, not a required brand. [17]
Disposable nitrile gloves, SUPPLYAID RRS-NDG100XL, 100 count, XL — $11.97 at Home Depot, October 2026; replace when splashed, torn or contaminated. An example pack, not a certification for every acrylate and IPA contact duration. [18]

Yearly running cost

At $21.99 per kg, 1 kg per year is $21.99 and 5 kg per year is $109.95 before shipping and tax; these are usage scenarios, not measured average annual consumption. An illustrative 5 kg per year hobby scenario totals $145.90: five $21.99 resin bottles ($109.95) plus two $11.99 32-oz IPA bottles ($23.98) plus one $11.97 100-count glove pack. It excludes printer electricity, cleaning tools, UV-curing machine, air extraction, waste treatment, release film, replacement LCD and safety gear beyond that pack. Electricity depends on the owner’s exact MSLA printer, lamp, heater, wash and cure station, layer count and durations, so no resin-only wattage or annual kWh figure exists. No mandatory subscription is required to purchase or use Standard Resin itself. [1][2][17][18]

When it is a good buy

October 25, 2026 US-facing retail observations, not guaranteed delivered prices: Anycubic US original Standard Resin Gray 1 kg at $21.99 (crossed-out $29.99); Anycubic US Standard Resin V2 Gray 1 kg at $23.99; Anycubic US ABS-Like Resin Pro 2 Gray 1 kg at $28.99; ELEGOO US Standard Resin V2.0 Gray 1 kg at $19.99; ELEGOO US ABS-Like Resin V2.0 Gray 1 kg at $26.99. ELEGOO indicates shipping is calculated at checkout with free shipping on orders above $50. A marketplace vendor listing at $11.99 cannot be safely treated as verified current authorized US supply. [1][3][12][14][15][16]

Editorial thresholds: at or below $15 per kg new, with verified expiry, genuine formulation and reasonable shipping, is attractive for display or calibration print volume, though no verified unconditional single-bottle US official offer at $15 was established. $16-20 is decent for a trusted fresh original Standard bottle if decorative prints dominate; above $19.99 an in-stock ELEGOO Standard V2.0 is worth comparing on a printer-specific profile basis. $21-22 is the normal official direct price; buy only with an already working profile or for its colors. At $23 or more, favor Anycubic Standard Resin V2 at $23.99 for buyers primarily concerned with brittleness, or Anycubic ABS-Like Resin Pro 2 at $28.99 or ELEGOO ABS-Like Resin V2.0 at $26.99 for frequently handled minis. [1][3][12][14][15][16]

Alternatives: Anycubic Standard Resin V2 Gray 1 kg ($23.99) is the better choice when breakage from handling matters and keeping Anycubic’s workflow is desirable. ELEGOO Standard Resin V2.0 Gray 1 kg ($19.99) is the better choice when lower one-bottle cost matters and the owner will calibrate a different manufacturer’s resin. Anycubic ABS-Like Resin Pro 2 Gray 1 kg ($28.99) or ELEGOO ABS-Like Resin V2.0 Gray 1 kg ($26.99) is the better choice for frequently transported minis, fragile projections and parts that need some flex rather than maximum stiffness. [12][15][14][16]